Fold aarch64 feature +fp into +neon
Arm's FEAT_FP and Feat_AdvSIMD describe the same thing on AArch64:
The Neon unit, which handles both floating point and SIMD instructions.
Moreover, a configuration for AArch64 must include both or neither.
Arm says "entirely proprietary" toolchains may omit floating point:
https://developer.arm.com/documentation/102374/0101/Data-processing---floating-point
In the Programmer's Guide for Armv8-A, Arm says AArch64 can have
both FP and Neon or neither in custom implementations:
https://developer.arm.com/documentation/den0024/a/AArch64-Floating-point-and-NEON
In "Bare metal boot code for Armv8-A", enabling Neon and FP
is just disabling the same trap flag:
https://developer.arm.com/documentation/dai0527/a
In an unlikely future where "Neon and FP" become unrelated,
we can add "[+-]fp" as its own feature flag.
Until then, we can simplify programming with Rust on AArch64 by
folding both into "[+-]neon", which is valid as it supersets both.
"[+-]neon" is retained for niche uses such as firmware, kernels,
"I just hate floats", and so on.
I am... pretty sure no one is relying on this.
An argument could be made that, as we are not an "entirely proprietary" toolchain, we should not support AArch64 without floats at all. I think that's a bit excessive. However, I want to recognize the intent: programming for AArch64 should be simplified where possible. For x86-64, programmers regularly set up illegal feature configurations because it's hard to understand them, see https://github.com/rust-lang/rust/issues/89586. And per the above notes, plus the discussion in https://github.com/rust-lang/rust/issues/86941, there should be no real use cases for leaving these features split: the two should in fact always go together.
- Fixesrust-lang/rust#95002.
- Fixesrust-lang/rust#95064.
- Fixesrust-lang/rust#95122.
Arm's FEAT_FP and Feat_AdvSIMD describe the same thing on AArch64:
The Neon unit, which handles both floating point and SIMD instructions.
Moreover, a configuration for AArch64 must include both or neither.
Arm says "entirely proprietary" toolchains may omit floating point:
https://developer.arm.com/documentation/102374/0101/Data-processing---floating-point
In the Programmer's Guide for Armv8-A, Arm says AArch64 can have
both FP and Neon or neither in custom implementations:
https://developer.arm.com/documentation/den0024/a/AArch64-Floating-point-and-NEON
In "Bare metal boot code for Armv8-A", enabling Neon and FP
is just disabling the same trap flag:
https://developer.arm.com/documentation/dai0527/a
In an unlikely future where "Neon and FP" become unrelated,
we can add "[+-]fp" as its own feature flag.
Until then, we can simplify programming with Rust on AArch64 by
folding both into "[+-]neon", which is valid as it supersets both.
"[+-]neon" is retained for niche uses such as firmware, kernels,
"I just hate floats", and so on.
`Layout` is another type that is sometimes interned, sometimes not, and
we always use references to refer to it so we can't take any advantage
of the uniqueness properties for hashing or equality checks.
This commit renames `Layout` as `LayoutS`, and then introduces a new
`Layout` that is a newtype around an `Interned<LayoutS>`. It also
interns more layouts than before. Previously layouts within layouts
(via the `variants` field) were never interned, but now they are. Hence
the lifetime on the new `Layout` type.
Unlike other interned types, these ones are in `rustc_target` instead of
`rustc_middle`. This reflects the existing structure of the code, which
does layout-specific stuff in `rustc_target` while `TyAndLayout` is
generic over the `Ty`, allowing the type-specific stuff to occur in
`rustc_middle`.
The commit also adds a `HashStable` impl for `Interned`, which was
needed. It hashes the contents, unlike the `Hash` impl which hashes the
pointer.
add address sanitizer fo android
We have been being using asan to debug the rust/cpp/c mixed android application in production for months: recompile the rust library with a patched rustc, everything just works fine. The patch is really small thanks to `@nagisa` 's refactoring in https://github.com/rust-lang/rust/pull/81866
r? `@nagisa`
Add well known values to `--check-cfg` implementation
This pull-request adds well known values for the well known names via `--check-cfg=values()`.
[RFC 3013: Checking conditional compilation at compile time](https://rust-lang.github.io/rfcs/3013-conditional-compilation-checking.html#checking-conditional-compilation-at-compile-time) doesn't define this at all, but this seems a nice improvement.
The activation is done by a empty `values()` (new syntax) similar to `names()` except that `names(foo)` also activate well known names while `values(aa, "aa", "kk")` would not.
As stated this use a different activation logic because well known values for the well known names are not always sufficient.
In fact this is problematic for every `target_*` cfg because of non builtin targets, as the current implementation use those built-ins targets to create the list the well known values.
The implementation is straight forward, first we gather (if necessary) all the values (lazily or not) and then we apply them.
r? ```@petrochenkov```
ARM: Only allow using d16-d31 with asm! when supported by the target
Support can be determined by checking for the "d32" LLVM feature.
r? ```````````````@nagisa```````````````
The previous approach of checking for the reserve-r9 target feature
didn't actually work because LLVM only sets this feature very late when
initializing the per-function subtarget.
Adopt let else in more places
Continuation of #89933, #91018, #91481, #93046, #93590, #94011.
I have extended my clippy lint to also recognize tuple passing and match statements. The diff caused by fixing it is way above 1 thousand lines. Thus, I split it up into multiple pull requests to make reviewing easier. This is the biggest of these PRs and handles the changes outside of rustdoc, rustc_typeck, rustc_const_eval, rustc_trait_selection, which were handled in PRs #94139, #94142, #94143, #94144.
asm: Allow the use of r8-r14 as clobbers on Thumb1
Previously these were entirely disallowed, except for r11 which was allowed by accident.
cc `@hudson-ayers`
mips64-openwrt-linux-musl: correct soft-foat
MIPS64 targets under OpenWrt require soft-float fpu support.
Rust-lang requires soft-float defined in tuple definition and
isn't over-ridden by toolchain compile-time CFLAGS/LDFLAGS
Set explicit soft-float for tuple.
Signed-off-by: Donald Hoskins <grommish@gmail.com>
Add MemTagSanitizer Support
Add support for the LLVM [MemTagSanitizer](https://llvm.org/docs/MemTagSanitizer.html).
On hardware which supports it (see caveats below), the MemTagSanitizer can catch bugs similar to AddressSanitizer and HardwareAddressSanitizer, but with lower overhead.
On a tag mismatch, a SIGSEGV is signaled with code SEGV_MTESERR / SEGV_MTEAERR.
# Usage
`-Zsanitizer=memtag -C target-feature="+mte"`
# Comments/Caveats
* MemTagSanitizer is only supported on AArch64 targets with hardware support
* Requires `-C target-feature="+mte"`
* LLVM MemTagSanitizer currently only performs stack tagging.
# TODO
* Tests
* Example
Apply noundef attribute to &T, &mut T, Box<T>, bool
This doesn't handle `char` because it's a bit awkward to distinguish it from `u32` at this point in codegen.
Note that this _does not_ change whether or not it is UB for `&`, `&mut`, or `Box` to point to undef. It only applies to the pointer itself, not the pointed-to memory.
Fixes (partially) #74378.
r? `@nikic` cc `@RalfJung`
MIPS64 targets under OpenWrt require soft-float fpu support.
Rust-lang requires soft-float defined in tuple definition and
isn't over-ridden by toolchain compile-time CFLAGS/LDFLAGS
Set explicit soft-float for tuple.
Signed-off-by: Donald Hoskins <grommish@gmail.com>
Currently, we are thinking to use *-unknown-none targets instead
to define for every platform our own one (see hermitcore/rusty-hermit#197).
However, the current target aarch64-unknown-none-softfloat doesn't support
dynamic relocation. Our kernel uses this feature and consequently
we define a new target aarch64-unknown-hermitkernel to support it.
Add more *-unwind ABI variants
The following *-unwind ABIs are now supported:
- "C-unwind"
- "cdecl-unwind"
- "stdcall-unwind"
- "fastcall-unwind"
- "vectorcall-unwind"
- "thiscall-unwind"
- "aapcs-unwind"
- "win64-unwind"
- "sysv64-unwind"
- "system-unwind"
cc `@rust-lang/wg-ffi-unwind`
Add new target armv7-unknown-linux-uclibceabi (softfloat)
This adds the new target `armv7-unknown-linux-uclibceabi (softfloat)`. It is of course similar to `armv7-unknown-linux-uclibceabihf (hardfloat)` which was just recently added to rust except that it is `softfloat`.
My interest lies in the Broadcom BCM4707/4708/BCM4709 family, notably found in some Netgear and Asus consumer routers. The armv7 Cortex-A9 cpus found in these devices do not have an fpu or NEON support.
With this patch I've been able to bootstrap rustc, std and host tools `(extended = true)` to run on the target device for native compilation, allowing the target to be used as a development platform.
With the recent addition of `armv7-unknown-linux-uclibceabihf (hardfloat)` it looks like many of the edge cases of using the uclibc c-library are getting worked out nicely. I've been able to compile some complex projects. Some patching still needed in some crates, but getting there for sure. I think `armv7-unknown-linux-uclibceabi` is ready to be a tier 3 target.
I use a cross-toolchain from my project to bootstrap rust.
https://github.com/lancethepants/tomatoware
The goal of this project is to create a native development environment with support for various languages.
mips64-openwrt-linux-musl: Add Tier 3 target
Tier 3 tuple for Mips64 OpenWrt toolchain.
This add first-time support for OpenWrt. Future Tier3 targets will be added as I test them.
Signed-off-by: Donald Hoskins <grommish@gmail.com>
This doesn't handle `char` because it's a bit awkward to distinguish it
from u32 at this point in codegen.
Note that for some types (like `&Struct` and `&mut Struct`),
we already apply `dereferenceable`, which implies `noundef`,
so the IR does not change.
Enable combining `+crt-static` and `relocation-model=pic` on `x86_64-unknown-linux-gnu`
Modern `gcc` versions support `-static-pie`, and `rustc` will already fall-back to `-static` if the local `gcc` is too old (and hence this change is optimistic rather than absolute). This brings the `-musl` and `-gnu` targets to feature compatibility (albeit with different default settings).
Of note a `-static` or `-static-pie` binary based on glibc that uses NSS-backed functions (`gethostbyname` or `getpwuid` etc.) need to have access to the `libnss_X.so.2` libraries and any of their dynamic dependencies.
I wasn't sure about the `# only`/`# ignore` changes (I've not got a `gnux32` toolchain to test with hence not also enabling `-static-pie` there).
