Allow a unique name to be assigned to dataflow graphviz output
Previously, if the same analysis were invoked multiple times in a single compilation session, the graphviz output for later runs would overwrite that of previous runs. Allow callers to add a unique identifier to each run so this can be avoided.
Make delegation methods of `std::net::IpAddr` unstably const
Make the following methods of `std::net::IpAddr` unstable const under the `const_ip` feature:
- `is_unspecified`
- `is_loopback`
- `is_global`
- `is_multicast`
Also adds a test for these methods in a const context.
Possible because these methods delegate to the inner `Ipv4Addr` or `Ipv6Addr`, which were made const ([PR#76205](https://github.com/rust-lang/rust/pull/76142) and [PR#76206](https://github.com/rust-lang/rust/pull/76206)), and the recent stabilization of const control flow.
Part of #76205
r? @ecstatic-morse
DroplessArena: Allocate objects from the end of memory chunk
Allocating from the end of memory chunk simplifies the alignment code
and reduces the number of checked arithmetic operations.
Add fast path for match checking
This adds a fast path that would reduce the complexity to linear on matches consisting of only variant patterns (i.e. enum matches). (Also see: #7462) Unfortunately, I was too lazy to add a similar fast path for constants (mostly for integer matches), ideally that could be added another day.
TBH, I'm not confident with the performance claims due to the fact that enums tends to be small and FxHashMap could add a lot of overhead.
r? `@Mark-Simulacrum`
needs perf
The main use case of TrustedLen is allowing APIs to specialize on it,
but no use of it uses that specialization. Instead, only the .len()
function provided by ExactSizeIterator is used, which is already
required to be accurate.
Thus, the TrustedLen requirement on BuilderMethods::switch is redundant.
The (internal) std::io::lazy::Lazy was used to lazily initialize the
stdout and stdin buffers (and mutexes). It uses atexit() to register a
destructor to flush the streams on exit, and mark the streams as
'closed'. Using the stream afterwards would result in a panic.
Stdout uses a LineWriter which contains a BufWriter that will flush the
buffer on drop. This one is important to be executed during shutdown,
to make sure no buffered output is lost. It also forbids access to
stdout afterwards, since the buffer is already flushed and gone.
Stdin uses a BufReader, which does not implement Drop. It simply forgets
any previously read data that was not read from the buffer yet. This
means that in the case of stdin, the atexit() function's only effect is
making stdin inaccessible to the program, such that later accesses
result in a panic. This is uncessary, as it'd have been safe to access
stdin during shutdown of the program.
---
This change removes the entire io::lazy module in favour of
SyncOnceCell. SyncOnceCell's fast path is much faster (a single atomic
operation) than locking a sys_common::Mutex on every access like Lazy
did.
However, SyncOnceCell does not use atexit() to drop the contained object
during shutdown.
As noted above, this is not a problem for stdin. It simply means stdin
is now usable during shutdown.
The atexit() call for stdout is moved to the stdio module. Unlike the
now-removed Lazy struct, SyncOnceCell does not have a 'gone and
unusable' state that panics. Instead of adding this again, this simply
replaces the buffer with one with zero capacity. This effectively
flushes the old buffer *and* makes any writes afterwards pass through
directly without touching a buffer, making print!() available during
shutdown without panicking.
- Suggest `x.py setup` if config.toml doesn't exist yet (twice, once
before and once after the build)
- Prompt for a profile if not given on the command line
- Print the configuration file that will be used
- Print helpful starting commands after setup
- Link to the dev-guide after finishing
- Note that distro maintainers will see the changelog warning
const_evaluatable_checked: extend predicate collection
We now walk the hir instead of using `ty` so that we get better spans here, While I am still not completely sure if that's
what we want in the end, it does seem a lot closer to the final goal than the previous version.
We also look into type aliases (and use a `TypeVisitor` here), about which I am not completely sure, but we will see how well this works.
We also look into fn decls, so the following should work now.
```rust
fn test<T>() -> [u8; std::mem::size_of::<T>()] {
[0; std::mem::size_of::<T>()]
}
```
Additionally, we visit the optional trait and self type of impls.
r? `@oli-obk`
